Adjustable Gain Electret Microphone Amplifier Sensor GY-MAX4466

6,95 €
+ 6,49 € Αποστολή

Adjustable Gain Electret Microphone Amplifier Sensor GY-MAX4466

  • Μάρκα: Unbranded
Πωλήθηκε από:

Adjustable Gain Electret Microphone Amplifier Sensor GY-MAX4466

  • Μάρκα: Unbranded

6,95 €

Αποθήκευση 27,00 € (79%)

Συνιστώμενη τιμή

33,95 €
Σε απόθεμα
+ 6,49 € Αποστολή
Πωλήθηκε από:

6,95 €

Αποθήκευση 27,00 € (79%)

Συνιστώμενη τιμή

33,95 €
Σε απόθεμα
+ 6,49 € Αποστολή

Δεχόμαστε τους ακόλουθους τρόπους πληρωμής

Περιγραφή

Add an ear to your project with this well-designed electret microphone amplifier. This fully assembled and tested board comes with a 20-20KHz electret microphone soldered on. For the amplification, we use the Maxim MAX4466, an op-amp specifically designed for this delicate task! The amplifier has excellent power supply noise rejection, so this amplifier sounds really good and isn't nearly as noisy or scratchy as other mic amp breakouts we've tried! This breakout is best used for projects such as voice changers, audio recording/sampling, and audio-reactive projects that use FFT. On the back, we include a small trimmer pot to adjust the gain. You can set the gain from 25x to 125x. That's down to be about 200mVpp (for normal speaking volume about 6 inch away) which is good for attaching to something that expects 'line level' input without clipping, or up to about 1Vpp, Perfect for reading from a microcontroller ADC. The output is rail-to-rail so if the sounds gets loud, the output can go up to 5Vpp! Using it is simple: connect GND to ground, VCC to 2.4-5VDC. For the best performance, use the "quietest" supply available (on an Arduino, this would be the 3.3V supply). The audio waveform will come out of the OUT pin. The output will have a DC bias of VCC/2 so when its perfectly quiet, the voltage will be a steady VCC/2 volts (it is DC coupled). If the audio equipment you're using requires AC coupled audio, place a 100uF capacitor between the output pin and the input of your device. If you're connecting to an audio amplifier that has differential inputs or includes decoupling capacitors, the 100uF cap is not required. The output pin is not designed to drive speakers or anything but the smallest in-ear headphones - you'll need an audio amplifier (such as 3.7W stereo amp) if you want to connect the amp directly to speakers. If you're connecting to a microcontroller pin, you don't need an amplifier or decou
  • Fruugo ID: 424043039-892118766
  • EAN: 7366102330241

Πληροφορίες για την ασφάλεια του προϊόντος

Δείτε τις πληροφορίες για την ασφάλεια του προϊόντος που περιγράφονται παρακάτω

Die folgenden Informationen werden vom unabhängigen Drittanbieter bereitgestellt, der dieses Produkt verkauft.

Ετικέτες ασφάλειας προϊόντων

CE Mark
Αύξων αριθμός: HL7333281681860

Παράδοση & Επιστροφές

Αποστέλλεται σε 3 μέρες

  • STANDARD: 6,49 € - Παράδοση μεταξύ Τρί 04 Νοεμβρίου 2025–Τετ 12 Νοεμβρίου 2025

Αποστέλλεται από Κίνα.

Κάνουμε ό,τι καλύτερο μπορούμε για να εξασφαλίσουμε ότι τα προϊόντα που παραγγέλνετε αποστέλλονται σε εσάς πλήρως και σύμφωνα με τις προδιαγραφές σας. Παρ' όλα αυτά, αν παραλάβετε μία ελλιπή παραγγελία ή προϊόντα διαφορετικά από αυτά που παραγγείλατε ή αν υπάρχει κάποιος άλλος λόγος που δεν είστε ικανοποιημένοι με την παραγγελία, μπορείτε να την επιστρέψετε ολόκληρη ή κάποια προϊόντα από αυτή και να λάβετε πλήρη επιστροφή χρημάτων για τα προϊόντα. Προβολή πλήρους πολιτικής επιστροφών

Details zur Produktkonformität

Bitte beachten Sie die unten aufgeführten Konformitätsinformationen zu diesem Produkt.

Die folgenden Informationen werden vom unabhängigen Drittanbieter bereitgestellt, der dieses Produkt verkauft.

Κατασκευαστής:
Οι παρακάτω πληροφορίες αφορούν τα στοιχεία επικοινωνίας του κατασκευαστή του σχετικού προϊόντος που πωλείται στο Fruugo.

  • Huiliang Trading Official Store 2
  • Wuhan Cuijue E-commerce Co., Ltd.
  • 628 Wuluo Road, Floor 30, Block A
  • Zhongnan Street, Wuchang District
  • Wuhan
  • china
  • 430061
  • 18218768550@163.com
  • 13246484773

Υπεύθυνος στην ΕΕ:
Οι παρακάτω πληροφορίες αφορούν τα στοιχεία επικοινωνίας του επευθύνου στην Ε.Ε. Ο υπεύθυνος είναι ο καθορισμένος οικονομικός φορέας που εδρεύει στην Ε.Ε. και είναι υπεύθυνος για τις υποχρεώσεις συμμόρφωσης που αφορούν το σχετικό προϊόν που πωλείται στην Ευρωπαϊκή Ένωση.

  • Berrih Ethan
  • DISCOUNT INDUSTRY
  • 10 Rue Des Grands Pres, 60230 Chambly, Oise, France
  • Chambly
  • France
  • 60230
  • DISCOUNT-INDUSTRY@outlook.com
  • 0033 748562127